DUSKTEC 24V LED Driver 15W 630mA, Low Voltage LED Transformer AC 240V to DC 24 Volt, Constant Voltage Power Supply for Led Strip Lights G4 MR11 and MR16 Light Bulbs, 112 x 44 x 16 mm

Used this as a small transformer for a ring wired door bell works fine.

The installation process was a breeze. The unit is compact and lightweight, making it easy to mount in various locations.One of the standout features of this LED driver is its constant voltage output.This consistency has significantly improved the performance and longevity of my LED lights.Durability is another aspect where this power supply shines. The build quality feels solid, and it's evident that the manufacturer has put attention to detail into its construction. It has been running flawlessly for a while now, even under continuous usage.Moreover, the safety features give me peace of mind. Overload protection and short-circuit protection ensure that my LED lights are safeguarded against potential electrical hazards, which is essential for any DIY project.

The LED driver is a compact design, easy to install and works as expected. I have it connected to a 3M 24V LED strip it has been working faultlessly for a couple of months. The transformer is a nice slim size making it easy to install either under or on top of cabinets without it being visible. Overall, a decent transformer at a reasonable price.

This 24V LED driver is exceptionally well made. The case is sturdy, but can be taken apart with minimal effort - IF you take it apart, be warned putting it back together: the back is polarised, but the board is not - so con't put it back in the wrong way round - or the case labels will be wrong!!The capacitors aren't "Panasonics", but neither are they cheap. And there is a LOT of capacitance on the board - which all helps for a smoother power supply - essential in lighting.Although there is good heat sinking, be aware the unit does NOT have any air flow holes, so if you drive it to its maximum for a long time, it's likely to get warm - although I did NOT find this on my relatively short run (10m).Which leads to the fact that they say it can be used in "damp" areas - which I probably would NOT do, as the case is NOT "IP rated" ...This could be resolved with some sugru (or other silicon sealant) - but as it stands I'd probably keep it somewhere dry.The soldering is clean (no dry solder joints) - and has been washed (to remove the flux) so it doesn't have that "new electronics" smell - both are a sign of good productionThere is a good mains break on the board to assure no spark jump. Indicative of good PCB design.I see one review comments that there is no Earth connection - be assured this type of device does NOT require one.I have every expectation that this will still be working in years to come - and in years to come, when the capacitors start to get old, it is easy to repair :) ...5*

I got this driver to enable me to install some floor level LED strips in the kitchen and 24V 60W provides sufficient enough power for my needs without causing the strips to dim towards the end of the run.What I like about this is the simple design and the clever way that the cables are installed and covered to prevent accidental shocks. Wiring it up was straightforward just like any other driver and it worked without any noticeable buzzing or without getting hot.It's a slim driver so you could use this under wall cabinets and it will be hidden out of sight but this didn't matter to me because it's behind the base board.At the time of me reviewing this, it's selling for £14 which is within similar prices of other drivers on the market so I'd say it was good value.

This is a nice 24V power supply, primarily aimed at LED strips of course, but quite suitable for other applications too. I am using it with 24V LED strips, drawing about 1.95A (about 47W); in testing I found the output voltage to be rock steady at almost exactly 24v (varied slightly between 24.01 and 24.03) across the range from no load up to 47W - I don't have any more 24V LEDs handy to try loading up all the way to 60W.Its beautifully slim, but interally the design looks good - look like good quality components, with good separation from mains to ELV side.Will definitely buy more of these - there's also a 12V version that looks interesting.

Does exactly what it says so can't fault it. Simple compact design.

So far works great easy to set up

Använde den till spotlight ut.

Bin zufrieden

Parfait

Costruzione robusta. Basso profilo e di facile installazione.