Nano Polymer Adhesive (50ml) - Ultimate 3D Printing Bed & Build Plate Adhesion - No Mess, Non-Toxic, Works for PLA, ABS, PEI, PEEK, Nylon, PC and More. Easy Application, Easy to Clean!

Absolutely amazing glue. I like to work with lots of different materials quite frequently. From PLA to PETG, ABS, ASA, Polycarbonate, Nylon, PPS, and several Carbon Fiber composites. I wanted a glue with strong reliable adhesion, and after looking at certain options such as magigoo, I found it a bit annoying to have to use and purchase various formulations of glue for all the different materials I use, and wished there was an "All in one" glue that just works with everything. I then discovered this stuff after watching some videos from Visionminer on YouTube and it sounded exactly like the glue I was looking for. Ordered some and let me tell you, it works with EVERYTHING I mentioned earlier and more. Super simple to apply with the included applicator brush, dries in seconds, hit print, and walk away knowing that I won't have any issues with bed adhesion. Only thing it doesn't work with is polypropylene, but that stuff has trouble sticking no matter what method of adhesion you use. Other than that, EVERY. SINGLE. FILAMENT. has worked for me with this glue and I cannot recommend it enough. The price is more than worth it for the peace of mind alone, and it will last you a good while as well since one application tends to last for several prints. 10/10

This adhesive is simply incredible and unmated when it comes to printing PC or ABS on a PEI build plate. PC on bare PEI will over-stick and ruin the PEI. ABS on PEI is a challenge in that the surface has to be meticulously clean with ISO. Though, this Vision Miner adhesive removes all the challenges and makes ABS effortless and perfect every time on PEI build plates. My time is scarce and valuable. Thus, a perfect print that does not elephant foot or peel is worth a few bucks on this adhesive.My process is to apply a few lines of adhesive to a cold PEI build plate and then brush into a thin layer with a foam 1in paint brush. From there, I often toss the plate on to a hot magnetic bed to dry. I find that I only need to re-apply after about 5-10 prints. The results are so worth it. If you have struggled with ABS or PC, give this a go!

Im printing with Sunlu PETG.8-12hours @60c in a Sunlu S2.Textured PEI plate.75c Bed 245c extruder.150-200mm speedI've had good success on my Bambu P1S prior to this stuff, but a couple large 24hour prints were damaged on removal from the plate due to the Bambu liquid glue just brutally sticking due to the higher bed temp and length of time.I thoroughly cleaned my plate with Dawn to degrease and 99% iso afterwards and applied this Nano-Adhesive.It dries extremely quickly. I've since done half dozen prints and am stunned how easy this stuff allows prints to come off the plate. It was even easier than no glue at all.Its disturbing the first time because you think the glue was so weak...no its just designed to hold properly during the print then release easily once the plate cools. I now give my prints 10-15min of cool down and can push them off with just fingertips. 100% got my value.

I’ve tried several plate adhesives, including Bambu Lab’s Liqui Glue, Magigoo, and standard glue sticks, but Vision Miner Nano Polymer is by far the best I’ve ever used. It’s extremely easy to apply and lasts a long time.I was having trouble with PETG sticking to one of my G10 build plates. After applying Nano Polymer, the PETG stuck perfectly during printing, and once the plate cooled down, the parts popped right off without any issue. Even after printing multiple parts in the same spot, adhesion remained strong.This has become my go-to adhesive anytime I run into adhesion problems. I primarily print with PLA and PETG, so I haven’t tested it with more exotic filaments, but based on my experience, I’d highly recommend it and I’d be confident it works well with other materials too.The only issue I had initially was applying too little adhesive. After watching their instructional video, I realized I wasn’t using enough. Now I follow their method: draw an “X”, circle it, and brush it in two directions. Since then, it’s worked amazingly well.

IT WORKS!Complicated PETG part on Prusa CoreOne had problems with edges lifting during the long print cycle. Heated chamber helps but it isn't perfect. Nano Polymer fixed this problem completely!!!!!!!!I've only done a day of printing but the results have been astounding. I have done 4 prints without replacing the surface but I really wouldn't mind if I have to reapply every time. Wasting a 7-1/2 hour print was pretty awful.I wish I have known about this sooner!

Let me tell you, the Vision Miner Nano Polymer 3D Glue has completely blown me away. I've wrestled with my fair share of adhesives over the years in this hobby, and honestly, this stuff is in a league of its own. The adhesion it provides is just phenomenal – prints stick firmly to the bed without any annoying warping or lifting, even with tricky materials.But it's not just about the stick; the release is equally impressive. Once the bed cools, parts practically detach themselves, leaving a clean surface behind. No more scraping and potentially damaging prints!The application is smooth and even, and a little goes a long way, which means this bottle is going to last. Honestly, the reliability and ease of use this glue provides have made my 3D printing experience so much more enjoyable and stress-free.Consider me a convert. From this point forward, Vision Miner Nano Polymer 3D Glue is the only adhesive I'll be reaching for. It's simply the best I've ever used.

This is great glue, it has helped keep my prints on the bed, I haven’t cleaned it off yet but works well. It comes with a brush the only thing I would change is coming with a roller top would make it easier to use but it works great.